The Foundation of Plumbing Skills for Bathtub Installation
The Foundation of Plumbing Skills for Bathtub Installation
Blog Article
This great article down below about How to Install a Bathtub Yourself is extremely intriguing. Don't miss out on it.
Setting up a bath tub isn't exactly rocket science, yet it does require solid plumbing, carpentry, and in some cases, tiling skills. Replacing an old bathtub with a brand-new one is additionally a reasonably tough job. If the old tub is conveniently obtainable, the task can move easily; if you need to open up a wall to remove the old tub and place the new bath tub, the task is much harder. In either case, the job is within a house handyman's skills, although you will certainly need an assistant to leave the old bathtub and embeded in the brand-new one. See to it you have qualified yourself for the job and are comfortable attempting it. As opposed to working with a specialist to take over a halfway-completed task, it is far better to consider utilizing one prior to you start. Opportunities are you may require an expert plumber to make tube connections.
This short article will certainly help you mount a brand-new bath tub in your restroom if you have currently acquired a brand-new bathtub and do not need to transform the arrangement of your previous water supply pipelines.
Your tools and product checklist need to make up the following:
Preparing for the Setup
Firstly, the supporting frame provided with the bath needs to be fitted (if required) according to the supplier's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is essential to make certain that if the faucet includes a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bath, it is also practical to fit a supporting plate under the taps unit to avoid pressure on the bathtub.
Fit the versatile faucet ports to the bottom of the two faucets making use of 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you utilize every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be suited its last placement.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installation, after that the first thing you should do is detach the supply of water. After doing so, activate the faucets to drain pipes any water continuing to be in the system. The procedure of removing the existing taps can be rather bothersome as a result of the restricted access that is commonly the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the faucets. Have a cloth all set for the continuing to be water that will certainly come from the pipes. When the supply pipes have actually been removed, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single faucets from turning throughout this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any old securing substance.
Before going on to fit the new taps, compare the pipe links on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Mounting the Bathtub
Making use of both wooden boards under its feet, put the bathtub in the needed setting. The wooden boards are handy in evenly spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto four little factors.
The following goal is to guarantee that the tub is leveled all round. This can be attained by examining the spirit level and also readjusting the feet on the bath tub until the spirit level checks out degree.
To set up faucets, fit all-time low of the outermost versatile faucet adapter to the suitable supply pipe by making a compression sign up with; after that do the very same for the various other tap.
Turn on the water supply and check all joints as well as new pipework for leakages as well as tighten them if required. Load the bathtub as well as likewise examine the overflow electrical outlet and the regular outlet for leaks.
Ultimately, take care of the bath paneling as described in the producer's instruction manual. Tiling as well as securing around the tub must wait till the bathtub has actually been used a minimum of once as this will resolve it right into its final placement.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will certainly require a plastic adapter to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end gives a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the tap in the placing opening in the bath/basin making sure that the washing machines are in location between the faucet as well as the sink. Secure the faucet in place with the producer provided backnut. As soon as the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with typical faucet adapters. The previous kind needs to be connected to the tap finishes initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bathroom satisfies the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to crack an inflexible seal, triggering the water to pass through the wall between the bathroom and also the tiling, bring about issues with moisture and also possible leaks to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your fixtures as well as fittings. They are sold in tubes as well as cartridges, and also can securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of drenched paper or soft rope. Remember to always load the bath tub with water before sealing, to permit the motion experienced when the bathtub remains in usage. The sealer can split relatively early if you do not take into consideration this activity prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also conveniently available on the marketplace. It is recommended to fit the ceramic tiles making use of water-resistant or water-proof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was brought to that write-up on Tools You Need to Install a New Bathtub through someone on a different web property. Liked our posting? Please share it. Let someone else find it. We treasure reading our article about Installing A Bathtub.
Additional Resources Report this page